• 1 Post
  • 12 Comments
Joined 10 months ago
cake
Cake day: March 12th, 2024

help-circle

  • I recently set up a small home server and started trying to self host stuff. I found it pretty hard to get started. People have been very helpful on this community and other public forums, but I’m afraid it’s often not enough. They give me advice in trying this or that, doing this and avoiding that… but I still don’t understand more than half of the concepts that they use. I consider myself tech literate above the average user: I recently switched to Linux (after years on MacOS, using the command line, and even building a couple of programs from source), I also installed a custom ROM on my phone. I feel comfortable learning and doing these things… but still felt very very lost when trying to self host a few services. At the moment I settled for a local-only network where I run Jellyfin, Navidrome and Syncthing on OpenMediaVault. I’m lost with what I’d need to do to access my server from outside my local network, and terrified of doing something wrong and leaving a hole open so any hacker can access my server. I’d like to do it some day, but I’d rather have a safe local network than screw and get my data stolen or deleted.

    So, in my opinion, we would need good tutorials or a MOOC to explain the basics from scratch.





  • Thank you for this new tip, I think we found the problem: ports 80 and 443 are not open. After I installed nmap (which was surprisingly not present in my Raspbian installation), the output of nmap localhost reads:

    Not shown: 997 closed ports
    PORT    STATE SERVICE
    22/tcp  open  ssh
    53/tcp  open  domain
    631/tcp open  ipp
    

    I guess I did something wrong when following the tutorial (or the tutorial had some mistake, but I’d me more inclined to think the mistake was mine). I will try to clear this installation on docker and start all over again, then I will check nmap localhost again to see if it works fine then.

    Thank you very much for your support. I still feel quite lost, but I finally found out why this is not working and I can repeat the steps and pay special attention… or look for a different method (someone here suggested using Nextcloud All-In-One).


  • Thanks for your answer. I am indeed getting no warning on my browser, just “Unable to connect” on LibreWolf and “This site can’t be reached” on Chromium. I tried the same format (https://192.168.50.30:80) with ports 80, 8080 and 443. The only difference is it was always https:// (since I think my browsers are configured to force https everywhere).

    The out put of docker container ls looks like this:

    CONTAINER ID   IMAGE              COMMAND                  CREATED        STATUS                                  PORTS     NAMES
    95a71b3ce4f6   nextcloud:apache   "/entrypoint.sh apac…"   24 hours ago   Restarting (1) 30 seconds ago                     nextcloud-app-1
    590b07333fa1   nextcloud:apache   "/cron.sh"               24 hours ago   Restarting (1) Less than a second ago             nextcloud-cron-1
    337fd48a72e8   nextcloud-proxy    "/app/docker-entrypo…"   24 hours ago   Restarting (1) 17 seconds ago                     nextcloud-proxy-1
    401d57a50ec8   mariadb:10.6       "docker-entrypoint.s…"   24 hours ago   Restarting (1) 57 seconds ago                     nextcloud-db-1
    c6093edc9f71   redis:alpine       "docker-entrypoint.s…"   24 hours ago   Restarting (1) 9 seconds ago                      nextcloud-redis-1
    

    I notice that the “PORTS” column is empty. I am running Raspbian GNU/Linux 11 (bullseye) on my Raspberry Pi, yes.






  • Thank you, the ip a command helped me get the IP clear, however I am still not sure about the port. I tried with :80, :8080 and :443 (because 80 and 443 are the ones mentioned in the compose.yaml file, and I saw online that 8080 is also a common one?) but none of them worked :(.

    I think I will try zerotier, but first I need to be able to access NextCloud from my home network via the IP, which I’m currently unable to do. The tutorial I followed says

    The other option is to use a self-signed certificate. This certificate is signed by your own server and won’t be verifiable by any web browser unless you manually install the certificate.

    However, it doesn’t explain where that certificate will be stored nor how I can manually install it in the browser I want to use to access NextCloud. Could that help with my issue?